Additive Manufacturing of Mechatronic Integrated Devices

Sprache: Englisch

Verlag: Springer, 2022

303116220X / 9783031162206

Anbieter: AHA-BUCH GmbH, Einbeck, DeutschlandAHA-BUCH GmbH

Verkäufer/-in mit 5 Sternen

AbeBooks-Verkäufer/-in seit 14. August 2006

Softcover

Zustand: Neu

EUR 61,97

EUR 35,00 Versand 
Versand von Deutschland nach USA

Anzahl: 1 verfügbar

In den Warenkorb
30 Tage kostenlose Rückgabe

Artikelbeschreibung des Verkäufers

Druck auf Anfrage Neuware - Printed after ordering - In this dissertation a new process chain for the Additive Manufacturing of Mechatronic Integrated Devices (AMMID) is described, which provides a new way to manufacture 3-dimensional electronic devices based on the selective laser sintering (SLS) process using laser direct structuring (LDS) and metallization. The AMMID process chain meets the rising demand for highly functionalized parts, increasing individualization and shortening development cycles for electronic products.The development for this process chain is based on an extensive literature review that indicates that an SLS-based process chain has great potential to produce 3-dimensional electronic devices with properties and with the future perspective of being suitable for an individualized mass production. The biggest, initial, technical hurdle is an unstable SLS process using a conventional LDS additive. The compound of SLS material and LDS additive was analyzed with DSC, which shows that the additive changes the melting behavior of the polymer by reducing the sintering window. A fine metal powder as an alternative additive affects the sintering window less and enables a stable process. To choose a suitable particle size and content for the metal powder an analytical material model is provided, that predicts the additive particle distribution within the material. This material model deepens the understanding of the activation mechanism during laser activation, provides hands-on information for powder preparation and it is applied for the design of the experiment for the development of the process chain with the new material.Preliminary experiments are conducted along with the insights of the material model, which prove that redeposition is the main activation mechanism during laser activation with fine metal powders. Based on this, the process chain is developed, starting with a determination of a suitable additive content. A suitable material composition of a PA12 powder containing 2 wt.% of a copper powder with a mean particle diameter of 3.5 mim was identified. With regard to the laser activation, working laser parameters are developed (working parameter set feasible for all used post-process treatments: PRF = 1 kHz, dh = 25 mim, vs = 25 mm/s, tl = 20ns and P = 1.07 W). In this parameter development it is shown, that only closely located laser spots, enabling interaction of the laser pulses, are capable of activating the surface, while single laser pulses under applied conditions are not. By adding a post-process treatment as additional process step into the process chain, the quality of metallization and the size of design features could be improved. Chemical smoothing resulted in a complete reduction of unwanted metallization on non-activated surfaces. Conductor tracks with the minimal width of 300 mim could be realized. The process chain could be applied to demonstrator parts such as a drone housing and a PSU panel of an aircraft. Thus, this dissertation has raised the technology readiness level (TRL) from TRL2 to TRL6.Finally, an economic consideration provides insights on the cost structure of parts produced with the AMMID process. A comparison of AMMID and injection molding shows economic viability for small lot sizes, 400 parts in case of the drone housing and 150 parts in case of the PSU panel. Finally, the analysis of the cost structure gives advice which future developments in the process chain have the greatest effect on costs and provides prioritization. …

Bestandsnummer des Verkäufers 9783031162206

Titel
Additive Manufacturing of Mechatronic Integrated Devices
Autor
Friedrich Wilhelm Proes
Verlag
Springer
Erscheinungsjahr
2022
Zustand
Neu
Einband
Taschenbuch
Sprache
Englisch
ISBN-10
303116220X
ISBN-13
9783031162206
Artikelgewicht
451 Gramm
Abmessungen
240x168x13 mm

AHA-BUCH GmbH

Einbeck, Deutschland

Verkäufer/-in mit 5 Sternen

AbeBooks-Verkäufer/-in seit 14. August 2006

Versandkosten von Deutschland nach USA

Artikel7 bis 10 Werktage5 bis 7 Werktage
Erster ArtikelEUR 35,00EUR 45,00
Die Versandzeiten werden von den Verkäuferinnen und Verkäufern festgelegt. Sie variieren je nach Versanddienstleister und Standort. Sendungen, die den Zoll passieren, können Verzögerungen unterliegen. Eventuell anfallende Abgaben oder Gebühren sind von der Käuferin bzw. dem Käufer zu tragen. Die Verkäuferin bzw. der Verkäufer kann Sie bezüglich zusätzlicher Versandkosten kontaktieren, um einen möglichen Anstieg der Versandkosten für Ihre Artikel auszugleichen.

Zahlungsarten

  • Visa
  • Mastercard
  • American Express
  • Carte Bleue
  • Apple Pay
  • Google Pay
  • Banküberweisung
  • PayPal
  • Vorauskasse

Shopbeschreibung

Das Unternehmen AHA-BUCH GmbH: Seit der Gründung von AHA-BUCH im Juli 2005 ist unser Hauptziel, zufriedenen Kunden so schnell und so preisgünstig wie möglich ihren Bücherwunsch zu erfüllen. Unsere Firma beschäftigt 16 Mitarbeiter, die nur ein Ziel kennen: den Kunden und seine Wünsche! Auf über 3700 m2 Fläche haben wir über 100.000 Bücher, Modernes Antiquariat und Spiele auf Lager.

Spezialisierung

Kinderbücher & Kinderhör Casetten, German Books, Software, Natur & Tiere, Ratgeber, Sachbücher, Englische Bücher, Medizin & Gesundheit, Universität & Studium

Unternehmensdaten der Verkäuferin bzw. des Verkäufers

AHA-BUCH GmbH

Garlebsen 48
Einbeck, Deutschland 37574